| Shipbucket http://shipbucket.com./forums/ |
|
| Corvette class ship http://shipbucket.com./forums/viewtopic.php?f=18&t=79 |
Page 1 of 2 |
| Author: | didibii [ August 4th, 2010, 5:26 pm ] |
| Post subject: | Corvette class ship |
Ok,so i just drew this becoues i was bored this morning its nothing sourious just to get used to the idea of drawing,this is my own design but i dont really like doing own design ill start working on a never-build ship in a few days. So this is my ship. ![[ img ]](http://i748.photobucket.com/albums/xx123/turkishnavyguy/template20L201-1.png) please tell me what you think of it. |
|
| Author: | Vossiej [ August 4th, 2010, 5:42 pm ] |
| Post subject: | Re: Corvette class ship |
Not half bad, however the bridge could use some redesigning. Take an example by looking at other ship's bridges. |
|
| Author: | TimothyC [ August 4th, 2010, 6:27 pm ] |
| Post subject: | Re: Corvette class ship |
No way you are going to get that VLS in that spot in the hull. |
|
| Author: | didibii [ August 5th, 2010, 1:36 am ] |
| Post subject: | Re: Corvette class ship |
![[ img ]](http://i748.photobucket.com/albums/xx123/turkishnavyguy/template20L201-2.png) ok i canged the front of it and put a smaller VLS and added 1 more new thing to it. |
|
| Author: | ezgo394 [ August 5th, 2010, 2:42 am ] |
| Post subject: | Re: Corvette class ship |
I dont think theres such thing as a smaller VLS. Just put it on the superstructure aft of the mast. |
|
| Author: | didibii [ August 5th, 2010, 2:48 am ] |
| Post subject: | Re: Corvette class ship |
Look at the parts sheet,the VLS that lunches essm missle is smaller then the other VLS but you idea can help so ill try it. |
|
| Author: | didibii [ August 6th, 2010, 6:27 am ] |
| Post subject: | Re: Corvette class ship |
![[ img ]](http://i927.photobucket.com/albums/ad114/yusa40killerpt/template20L201-1.png) Ok finally done. |
|
| Author: | Blackbuck [ August 6th, 2010, 10:41 am ] |
| Post subject: | Re: Corvette class ship |
Your shuttering for a RHIB? Is encroaching upon the funnels for starters. |
|
| Author: | didibii [ August 6th, 2010, 6:40 pm ] |
| Post subject: | Re: Corvette class ship |
Wait... What? My ship doesn't need a RHIB. Does it? |
|
| Author: | Scifibug [ August 6th, 2010, 6:47 pm ] |
| Post subject: | Re: Corvette class ship |
No you need small craft for some of your ship's missions (inspections, movement between ships, etc.) at the very least you need some way to go on liberty when the ship has to anchor out. I think Blackbuck's concern is the size of the ship's boat and that it's position appears to be blocking the intakes to the engines. If you're using gas turbines they require a HUGE amount of air to operate. I suggest moving it forward more midships. |
|
| Page 1 of 2 | All times are UTC |
| Powered by phpBB® Forum Software © phpBB Limited https://www.phpbb.com/ |
|